P0136 - O2 Sensor Circuit Bank 1 Sensor 2
P0136 is a generic powertrain diagnostic trouble code indicating O2 Sensor Circuit Bank 1 Sensor 2. It relates to the Fuel & Air Metering system.
DTC Breakdown (SAE J2012)
| System | Powertrain (P) |
| Type | Generic |
| Subsystem | Fuel & Air Metering |
| Fault Index | 36 |
| Standard | SAE J2012 / ISO 15031-6 |
What does diagnostic code P0136 mean?
The engine control module logged P0136 because it detected a circuit malfunction in the oxygen (O2) sensor circuit for Bank 1, Sensor 2.
Severity Level & Driveability Details
Severity: Moderate
The engine cannot adjust fuel mixtures properly, leading to poor performance, low fuel economy, and potential catalyst damage over time.
Common Symptoms of P0136
- Check engine light illuminated.
- Poor fuel economy caused by incorrect oxygen sensor feedback.
- Engine stumbling, rough idling, or minor hesitation.
- Failing tailpipe emissions test due to incorrect exhaust feedback.
Typical Causes for P0136
- Failed oxygen sensor (Sensor 2 on Bank 1).
- Corroded wiring or loose electrical connector at the sensor plug.
- Blown O2 sensor circuit fuse.
- Exhaust leaks near the oxygen sensor location, introducing unmetered air.
Diagnostic and Troubleshooting Steps
A normal upstream sensor should oscillate rapidly between 0.1V and 0.9V. Monitor O2 sensor voltage output on a scan tool. If the signal is stuck or slow, verify reference voltage and heater resistance with a digital multimeter.
Typical Repairs and Fixes
- Replacing the oxygen sensor (Sensor 2 on Bank 1).
- Repairing damaged wiring harness or connector plugs at the sensor.
- Replacing the blown O2 sensor fuse.
- Repairing exhaust leaks near the sensor.
Sensor Location & Parts Involved
The oxygen sensor is located in the exhaust pipe, either upstream (Sensor 1) or downstream (Sensor 2) of the catalytic converter.
Clearing Code & Recurrence
Clear the code using an OBD2 scanner and perform a drive cycle to reset the monitors.
Emissions & Smog Inspection Impact
Can cause rich running (excess carbon monoxide and hydrocarbons) or lean running (excess nitrogen oxides).
Free Check Engine Code Cheat Sheet (PDF)
Got your answer? Keep the top 50 most common diagnostic codes, their meanings, severity levels, and quick fixes handy in your vehicle's glovebox.
Related Diagnostic Codes
Sources & References
This diagnostic guide is compiled and verified against the following authority sources:
- EPA Emissions OBD Guide
- SAE J2012 specifications
Frequently Asked Questions about P0136
What does the Bank 1 Sensor 2 O2 sensor circuit code P0136 mean?
The engine control module logged P0136 because it detected a circuit malfunction in the oxygen (O2) sensor circuit for Bank 1, Sensor 2.
Is it safe to drive with the Bank 1 Sensor 2 O2 sensor circuit code P0136 active?
Yes, but engine fuel efficiency will decrease until the sensor is replaced.
How much does it cost to repair a Bank 1 Sensor 2 O2 sensor circuit code P0136 fault?
Replacement parts cost $80-$200. Labor to replace the sensor is $70-$150 depending on rust and access.
What are the common causes of the Bank 1 Sensor 2 O2 sensor circuit code P0136?
Trigger conditions for the Bank 1 Sensor 2 O2 sensor circuit code P0136 include: Failed oxygen sensor (Sensor 2 on Bank 1)., Corroded wiring or loose electrical connector at the sensor plug., Blown O2 sensor circuit fuse..
Can I clear the check engine light for Bank 1 Sensor 2 O2 sensor circuit code P0136?
Clear the code using an OBD2 scanner and perform a drive cycle to reset the monitors.
Will the Bank 1 Sensor 2 O2 sensor circuit code P0136 cause an inspection failure?
Can cause rich running (excess carbon monoxide and hydrocarbons) or lean running (excess nitrogen oxides).